吃瓜tv / RF MATERIALS & FABRICATION
Taconic TLX PCB Materials: Grade Selection & Design
Reinforced RF cores for antennas and passive networks. Use the source context, engineering checks and project tools below to turn the material name into a usable fabrication specification.
Request a Taconic PCB quote
What to specify for TLX-8
Taconic TLX-8 is covered here as a named RF material. The current TLX-8 TDS lists Dk at 1 MHz and Df at 10 GHz. The overview guide groups values differently; keep the TDS method with your model.
| Field | Specification context |
|---|---|
| Material identity | TLX-8 |
| Reference Dk | 2.55 |
| Reference Df | 0.0018 |
| Test context | Dk: 1 MHz, 2.5.5.3; Df: 10 GHz, modified 2.5.5.5.1 |
| Thermal conductivity | 0.19 W/m路K; see specimen/test condition |
| Supply status | Confirm current grade, thickness, foil and order quantity; no stock promise |
Do not miss: The current TLX-8 TDS lists Dk at 1 MHz and Df at 10 GHz. The overview guide groups values differently; keep the TDS method with your model.
Reference trail: 路 路 . Numerical values are typical material references, not purchase acceptance limits, live stock or guaranteed fabricated performance.
The TLX suffix matters
| Grade | Historical nominal Dk | Source context |
|---|---|---|
| TLX-0 | 2.45 | Archived family identification |
| TLX-9 | 2.50 | Archived family identification |
| TLX-8 | 2.55 | Current TDS: Dk 1 MHz; Df 0.0018 at 10 GHz |
| TLX-7 | 2.60 | Archived family identification |
| TLX-6 | 2.65 | Archived family identification |
Confirm the individual source document for non-TLX-8 procurement. Do not apply the current TLX-8 Df and CTE to the entire historical series.
Woven reinforcement and the RF reference path
Woven glass supports the PTFE structure, but the electrical path still depends on local geometry, foil and dielectric thickness. Keep the glass style, copper profile and source revision in the material callout. For precision phase matching, investigate routing orientation and length over the reinforcement rather than treating nominal Dk as a complete description.
- Choose the TLX suffix before routing
- Check the dielectric-height tolerance
- Do not assign one Df or CTE to all historical TLX variants
Taconic PCB Design Workbench
The RF tool uses an editable model Dk; the preset is a supplier reference at its stated method and frequency. It is not a universal design Dk. Blank parameters stay blank until you provide a value. Geometry calculations do not approve a fabrication tolerance.
For microstrip, h is the dielectric separation to the reference plane; for symmetric stripline it is the total plane spacing. Propagation follows 位g = c/(f鈭毼礶ff). Thermal screening uses R = h/(kA). Read the selected model鈥檚 exclusions beside the result.
For more geometries and fabrication tolerance context, use the PCB impedance calculator and design guide.
From material callout to fabricated PCB
Material release
Name TLX-8, the supplier revision, thickness and foil. Separate approved substitutions from suggestions awaiting approval.
CAM and stackup
Review layer references, panelization, copper balance, minimum features and finished geometry. Choose the TLX suffix before routing.
Process definition
Use the applicable laminate and bonding guides. Agree drilling, hole-wall treatment and lamination details for this construction; do not assume a universal FR-4 recipe.
Patterning and final build
Control conductor geometry, hole quality, mask openings and finish on exposed RF areas. Include special edges, cavities or connectors in the release.
Inspection and acceptance
Define dimensional, netlist and impedance checks. RF loss or phase measurements need a separate coupon/fixture, frequency range and acceptance limit.
Review the manufacturing capability tables for general process limits and quality documentation and acceptance planning for supplier review. A listed material property is not a 吃瓜tv test report.
TLX-8 PCB cost & quotation brief
A quote for TLX-8 depends on the approved material construction, purchased sheet utilization, quantity, layer count, drilling/lamination work, finish and inspection scope. There is no defensible fixed 鈥淭aconic multiplier鈥� across these products. For older designations, sourcing confirmation may be the first cost decision.
Taconic PCB Cost & Quotation Brief
Use the brief without prices, or enter your own setup and fabrication-area allowances to explore a simple two-layer planning range. The tool does not contain verified current supplier rates. Hybrid, multilayer, bonding-film and RF-qualified builds are routed to engineering quotation.
| Cost question | Information to provide |
|---|---|
| Material | Exact code, thickness, foil, substitutions allowed or prohibited |
| Fabrication | Gerber/ODB++, drill data, stackup, copper, outline and special features |
| Acceptance | Net classes, impedance target/tolerance and any RF test fixture |
| Order | Quantity, requested delivery date, repeat-build needs and assembly scope |
TLX-8 questions before ordering
What does the TLX-8 material name guarantee?
It identifies a material or family to resolve in the supplier documentation. The exact code, thickness, foil and data-sheet revision still need to be specified. It does not guarantee 吃瓜tv stock, lead time or an application qualification.
Which Dk should I use in my RF model?
Dk: 1 MHz, 2.5.5.3; Df: 10 GHz, modified 2.5.5.5.1. Use a model Dk appropriate to your geometry and frequency. A process test value is useful reference data but is not automatically the effective permittivity of a microstrip.
Can I replace TLX-8 with another Taconic or Rogers grade?
The current TLX-8 TDS lists Dk at 1 MHz and Df at 10 GHz. The overview guide groups values differently; keep the TDS method with your model. Compare the complete electrical, mechanical and processing requirements, then approve the alternate explicitly.
What design detail deserves the first review?
Choose the TLX suffix before routing. Track the signal to its adjacent reference plane. A split or void can change the return path even if line width is correct.
Does a netlist test verify RF performance?
No. Netlist testing checks connectivity. RF performance requires defined measurement structures, frequency range, reference planes and limits. State the required measurement in the RFQ.
How do I obtain a usable quotation?
Send the fabrication files, drill data, stackup, exact material code, quantity and acceptance requirements. Include your requested date; the delivery commitment depends on sourcing and process review.
Next useful references: Taconic PCB manufacturing 路 full Taconic material directory 路 TLY-5 路 TLY-3.
Send the design with its material context
Preliminary files are welcome. Identify the design revision and open material decisions so the enquiry can address the actual manufacturing scope.
Send TLX-8 files for review